DNAx Nitrox membrane compressors. In other words a compressor that "De-Nitrogenises Air" (DNA), or in layman's terms, takes air throws away the nitrogen and saves what's left, "OXYGEN ENRICHED AIR".
The technology behind this system has been available for years but has only been utilised in industry due to the size, complexity, and cost of the membrane.

The new membranes now available do away with all these problems and provide small, easily maintained, cost-effective units that can be used with most compression systems or bought as a complete compression system in a purpose built cabinet.
 

• Charging rate : 80l/min - 6m3/h - 2.8 cfm
• Filling time cylinder : 10 L - 0-200 Bar 25 min
• Working pressure : 225 Bar 3200 psi
• Driven by : Single phase electric motor
• Power : 2,2 Kw - 3 HP
• Rpm : 2800 (230 V - 50 Hz) - 3400 (230 V - Hz / 115 V - 60 Hz)
• Full load Amps : 14 A (230 V - 50 Hz / 230 V - 60 Hz) - 29 A (115 V - 60 Hz)
• Measurements : H 55.8cm x L 129.5cm x W 40.6cm
• Weight : 63.5 KG
• Noise Level : 81.7 dB - ISO 3746
• Lubricating oil capacity : 300 cc (0.3 L) / 10,1 FL. OZ
• Lubricant : Airtek CE 555 synthetic lubricant
• Frame : Aluminium and powder coated steel
• Oil/Moisture separator : After last stage
• Filtration : Filter cartridge active carbon and molecular sieve
• % Max 0² : 40
• Safety valve : On the separator housing
• Interstage coolers and after coolers : Stainless steel
• Breathing Air : DIN 3188 EN12021 CGA E
• Membrane type : Nuvair Permea

DNAx Nitrox membrane compressors. In other words a compressor that "De-Nitrogenises Air" (DNA), or in layman's terms, takes air throws away the nitrogen and saves what's left, "OXYGEN ENRICHED AIR".
The technology behind this system has been available for years but has only been utilised in industry due to the size, complexity, and cost of the membrane.

The new membranes now available do away with all these problems and provide small, easily maintained, cost-effective units that can be used with most compression systems or bought as a complete compression system in a purpose built cabinet.
 

• Charging rate - 200l/min - 14m3/h - 7 cfm
• Driven by - Three phase electric motor
• Working pressure - 225 bar 3200 psi
• Noise Level - 80.7 dB - ISO 3746
• Weight - 130 KG
• Measurements - H 72cm x L 130cm x W 51cm
•  
• 24 - 40 % :O²

DNAx Nitrox membrane compressors. In other words a compressor that "De-Nitrogenises Air" (DNA), or in layman's terms, takes air throws away the nitrogen and saves what's left, "OXYGEN ENRICHED AIR".
The technology behind this system has been available for years but has only been utilised in industry due to the size, complexity, and cost of the membrane.

The new membranes now available do away with all these problems and provide small, easily maintained, cost-effective units that can be used with most compression systems or bought as a complete compression system in a purpose built cabinet.
 

• Charging rate - 240L/min - 14m3/h - 8.5 cfm
• Driven by - Three phase electric motors 2 x 5.5 Kw
• Working pressure - 225 bar 3200 psi
• Noise Level - 75 dB - ISO 3746
• Weight - 335 KG
• Measurements - H 133cm x L 89cm x W 85cm
•  
• 24% - 40% O²

The Nitrox LP 280 Rotary Silent production system consists of a rotary screw low pressure compressor that supplies air to a membrane system where oxygen rich air is separated away from nitrogen air. The oxygen rich air (nitrox) is then mixed and delivered to the intake of a high pressure compressor to be pumped into the tanks. The oxygen percentage is available from 22.40 % by adjusting the regulated air input pressure. The system utilizes a 7.5 Kw, 740l/m, 175 psi (12 bar) rotary screw compressor mounted with a three-phase electric motor in a silenced cabinet.

Compressor system components include: low pressure rotary screw compressor, volume tank with over pressure relief, condensate drain, motor and frame.

The nitrox system parts include: low pressure filtration to 0.003 ppm oil vapour, low pressure regulator, heater with automatic thermostat control, permeable membrane, mixing tube, compressor intake porting, permeate hose for connection to your exsiting HP compressor intake, inline oxygen sensor with analyzer to supply a reading of what oxygen % is going to your compressor and a fill oxygen % analyzer with high pressure to low pressure regulator to supply accurate readings of oxygen % from your compressor to the tanks being filled.

• Simplest, Most Cost Effective Nitrox Systems Available
• Pump LP Nitrox containing 24-40% Oxygen
• None of the Costs, Hassles, or Hazards of O2 Blending
• Systems to Fit Most HP Compressors
• Vertical cabinet Minimizes Space Requirements
• Rotary Screw Lp Compressor Provides Quietest Operation & Lowest Maintenance
• Nitrox Membrane System with (2) O2 Analyzers
• Microprocessor Controller Manages Pressures, Temperature, Run Time, Maintenance, & Diagnostics
• Automatic Shutdowns for High Pressure & Temperature
• Automatic Condensate Drain
• Use with 6-45 cfm HP Breathing Air Compressors
• Includes Grade D LP Filtration for Membrane

• One of the Simplest, Most Cost Effective Nitrox Systems Available
• Pump LP Nitrox containing 24-40% Oxygen
• None of the Costs, Hassles, or Hazards of O2 Blending
• Systems to Fit Most HP Compressors
• Vertical cabinet Minimizes Space Requirements
• Rotary Screw Lp Compressor Provides Quietest Operation & Lowest Maintenance
• Nitrox Membrane System with (2) O2 Analyzers
• Microprocessor Controller Manages Pressures, Temperature, Run Time, Maintenance, & Diagnostics
• Automatic Shutdowns for High Pressure & Temperature
• Automatic Condensate Drain
• Use with 6-45 cfm HP Breathing Air Compressors
• Includes Grade D LP Filtration for Membrane